dot dot
dot

หมวดสินค้า
ยี่ห้อสินค้า

  [Help]
dot
dot
ชื่อผู้ใช้ :
รหัสผ่าน :
เข้าสู่ระบบอัตโนมัติ :
bullet ลืมรหัสผ่าน
bullet สมัครสมาชิก
dot
dot
ตู้แรค rack ปลั๊กแจ๊ค สายสัญญาณ สายมัลติคอร์ PLUG JACK MULTICORE
dot




YAMAHA QL5  
รหัส : QL5
ยี่ห้อ : YAMAHA
รุ่น : QL5
ราคาปกติ :  970,000.00 บาท      

รายละเอียดย่อ :
ดิจิตอลมิกเซอร์ Digital Mixing Console 32 Analog input, 16 output, 8 Matrix.
รายละเอียดทั้งหมด :

 

YAMAHA QL5 ดิจิตอลมิกเซอร์ Digital Mixing Console 32 Analog input, 16 output, 8 Matrix.( Max 64 input via optional i/o ), Superior Dante Networking Built In.Fader configuration: 32 + 2 (Master), Stainless steel iPad support stays.

  • Mix channels: 64 mono, 8 stereo.
  • Busses: 16 mix, 8 matrix (Input to Matrix supported).
  • Local I/O: 32 in, 16 out.
  • Fader configuration: 32 + 2 (Master).
  • Stainless steel iPad support stays.

specifications

Sampling frequency rate Internal 44.1kHz / 48kHz
External 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm)
Signal delay Less than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz
Fader 100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders
Total harmonic distortion Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min.
Frequency response +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT
Dynamic range 112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min.
Hum & noise level Equivalent input noise -128dBu typ., Equivalent Input Noise, Input Gain=Max
Residual output noise -88dBu, Residual output noise, ST master off
Crosstalk -100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min.
Power requirements 100-240V 50/60Hz
Power consumption 200W
Dimensions W 828mm(32.6in)
H 272mm(10.7in)
D 563mm(22.2in)
Net weight 21.8kg(48.1lb)
Accessories Owner’s Manual, dust cover, power cord, DVS license sheet
Options Mini-YGDAI cards *2 , Gooseneck Lamp LA1L, Nuendo Live
Others Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃

Crosstalk@1kHz : A 22kHz, 30dB/Oct filter is used to measure crosstalk.
Total Harmonic Distortion : An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion.
Hum & Noise : An A-Weight filter is used to measure hum &noise.

Analog input characteristics

Input Connectors GAIN Input
Impedance
Source
Impedance
Input level Connector
Sensitivity*¹ Nominal Max. before clip
INPUT
1-32 *6
+66dB 7.5 kΩ 50-600 Ω
Mics &
600 ΩLines
–82dBu
(61.6μV)
–62dBu
(0.616mV)
–42dBu
(6.16mV)
XLR-3-31
type
(Balanced) *2
–6dB –10dBu
(245mV)
+10dBu
(2.45V)
+30dBu
(24.5V)

*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level
controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu=0.775 Vms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the console software.
*6. QL1: INPUT1-16

Analog output characteristics

Output
Connectors
Output
Impedance
Load
Impedance
Maximum
Output
Level *5
Output Level Connector
Defined Level Maximum
Non-Clip Level
OMNI
OUT 1-16 *7
75 Ω 600 Ω
Lines
+24dB
(default)
+4dBu
(1.23V)
vt+24dBu
(12.3V)
XLR-3-32 type
(Balanced) *1
+18dB –2dBu
(616mV)
+18dBu
(6.16V)
PHONES 15 Ω 8 Ω
Phones
- 75mW *6 150mW Stereo Phone
Jack(TRS)
(Unbalanced) *2
40 Ω
Phones
- 65mW *6 150mW

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND).
*3. 0 dBu=0.775 Vms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position.
*7. QL1: OMNI OUT 1-8

Digital input/output specifications

Connectors Format Data length Level Audio Connector
Primary/Secondary Dante 24bit or 32bit 1000Base-T 64ch Input/64ch
Output@48kHz *1
EtherCON Cat5e

*1. QL1: 32ch Input/32ch Output@48kHz

Digital output specifications

Connectors Format Data length Level Connector
DIGITAL OUT AES/EBU AES/EBU Professional Use 24bit RS422 XLR-3-32 type (Balanced) *1

*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).


จำนวน      


niyomsilp hi-fi & studio co.,ltd @2017 All Rights